MODBUSEZ Plugin

[trendsetter]

Dear all,

I have the following Inverter:
DZB312B003.7L2DK
manual is here:
https://www.manualslib.com/manual/82887 ... tml#manual

I am quite clear about setting the control of the VFD to Modbus and I have a standard USB-RS454 adapter.
It seems that there is some communication possible, since the display is changing with Modbusez plugin used with UCCNC but I cannot get the spindle running. The Spindle is still in Stop mode and I don´t have any chance to change it. Any tipps from the expert how to execly configurate the plugin for this Invertere?

Standard Analog digital control works perfectly, but I need more I/O therefore I want to change to modbus.

BR
Michael

[Paklic]

Hi,
I bought a VFD ecogoo 9100-1t-00150gb.
Manual I found here: https://pan.baidu.com/s/1hsw6eYo
I found how to set rs485 that's ok, but I don't know how to turn on rs485.
Does anyone know how?
Thanks...
sorry my english is not good.

[Dan911]

Paklic go to page 1 of this thread and read how Battwell got his Ecogoo VFD working,

[Paklic]

Paklic go to page 1 of this thread and read how Battwell got his Ecogoo VFD working,

but my problem is different, i can't enable rs485 is not comunication.

I have set up for rs485:
P9.00 is the local address / 1
P9.01 is baud rate - 9600/3
P9.02 is N81for RTU / 0
this setting is ok.
I don't need hex command
How to enable rs485 + and rs485-?
I can't do it from the read manual.

I got hex commands to be useful
[at

9100 RS485.docx

hex command

(19.21 KiB) Downloaded 1060 times

manual:
tachment=1]9100 User manual.rar[/attachment]

[Paklic]

connected via modbus poll
Modbus not connection

[v8kid]

Paklic go to page 1 of this thread and read how Battwell got his Ecogoo VFD working,

I must be dumb too because I went to P1 and couldn't figure out what the parameter settings were either!
Is Paklic correct that these are the only 3 parameters that require changing I assumed P0.01 P0.02, P0.16 and P0.17 require changing too.
Cheers

[Battwell]

re ecogoo. read pages 2,3,4 of this forum thread.
all the info and head scratching is there!
ecogoo was one of the easier ones to work out.

[cofhal]

I am using screenset 2017.Install the MODBUSEZ16 plugin and I have a VDF Fuling DZB280 and everything works correctly, the only problem is that the speed I send (Sxxxx), the program is sent by the VDF but multiplied by 4. For this reason for example to set the speed to 10000 RPM I have to type in the MDI S2500.

[SiemonB]

Hi Dan,

Was hoping you could help me with the "Modbus Setup" Values.
I've gotten to the point where I succesfully can control my vfd with "Modbus Poll, but I've been trying for a while now but no luck.

Danfoss vlt 51manual https://files.danfoss.com/download/Drives/MG02K402.pdf

Thank you in advance!

[SiemonB]

Hi,

Looking for some help with my setup ( A Danfoss vlt51 Micro)
I've got it working over rs485 with "Modbus Poll", added some screengrabs from that.
When it comes to the plugin made by Dan I have some issues figuering out what goes where (manual added below)

Thank you in advance!

VFD Manual:
https://files.danfoss.com/download/Drives/MG02K402.pdf