Phone Number for CNCdrive

If you have a question about the software please ask it here.

Phone Number for CNCdrive

Postby Vance » Wed Sep 16, 2020 7:26 pm

Board repair status: I need to speak to the staff in Hungary.

What is the phone number?
________________________________________________________________
Vance
CNC Router Parts 48/96, 23,
ST-M5045 drivers
/ETH-5LPT/UCSB
Carveco Maker
Vance
 
Posts: 24
Joined: Fri Feb 28, 2020 12:07 am
Location: Houston

Re: Phone Number for CNCdrive

Postby cncdrive » Wed Sep 16, 2020 7:36 pm

+36709040565
cncdrive
Site Admin
 
Posts: 4887
Joined: Tue Aug 12, 2014 11:17 pm

Re: Phone Number for CNCdrive

Postby asuratman » Thu Sep 17, 2020 12:33 pm

If board got damage, can we it be repaired ? Send it to hungary ?
asuratman
 
Posts: 118
Joined: Sun Jan 28, 2018 1:50 pm

Re: Phone Number for CNCdrive

Postby cncdrive » Thu Sep 17, 2020 1:21 pm

Yes, we can attempt to repair, but ofcourse it depends on what and how damaged if it can be repaired and if it worth to repair.
There can be cases when a board is unrepairable, for example if the PCB board burns/damages.
And there can be cases when a board does not worth to repair, if so many components damages that the repair cost would be higher than a new board.

Ofcourse we can check the damaged board and can advice repairability and the cost involved.
cncdrive
Site Admin
 
Posts: 4887
Joined: Tue Aug 12, 2014 11:17 pm

Re: Phone Number for CNCdrive

Postby Vance » Tue Sep 29, 2020 1:52 pm

cncdrive wrote:+36709040565


I am dialing 011-36709040565 from the US and there is no answer. I have dialed it multiple times, once I received a recording but I could not understand the language. I was never able to leave a message.

What number should I dial (from the US) to reach the warranty department about the board I sent in June?
________________________________________________________________
Vance
CNC Router Parts 48/96, 23,
ST-M5045 drivers
/ETH-5LPT/UCSB
Carveco Maker
Vance
 
Posts: 24
Joined: Fri Feb 28, 2020 12:07 am
Location: Houston

Re: Phone Number for CNCdrive

Postby cncdrive » Tue Sep 29, 2020 2:30 pm

Hi,

There is no need to call, just email us please.
But I know your case and looked after it and we did not receive your board, my collegue said that it was returned to the sender by the post office.
They did notify us about the package arrival and asked for customs clearance, but we could not identify the package and so we did not know the content.
Then we finally identified your email and asked you about the content, because without knowing the package content we could not fulfill the customs papers.
But this was already too late and the post office said that the package was returned to the sender, because they do not store packages for more than 15days.
cncdrive
Site Admin
 
Posts: 4887
Joined: Tue Aug 12, 2014 11:17 pm

Re: Phone Number for CNCdrive

Postby cncdrive » Tue Sep 29, 2020 2:32 pm

And yes, my collegues are usually busy with doing emails and packaging and ordering parts etc., so sometimes there is nobody there to pick the phone up and not all my collegues speak english, this is why it is better to email, because in email you will get a hold of me or a collegue who knows English language.
cncdrive
Site Admin
 
Posts: 4887
Joined: Tue Aug 12, 2014 11:17 pm

Re: Phone Number for CNCdrive

Postby Vance » Tue Sep 29, 2020 2:48 pm

cncdrive wrote:Hi,

There is no need to call, just email us please.

I have, many many times.
cncdrive wrote:But I know your case and looked after it and we did not receive your board, my collegue said that it was returned to the sender by the post office.

The postal service still shows the package at the destination post office.

cncdrive wrote:They did notify us about the package arrival and asked for customs clearance, but we could not identify the package and so we did not know the content.

That is incorrect. On August 16th, I received this email

    We got a message from the Post office that there is a package for us from you.
    Could you tell me what is in the package? Did you write price on it?

    Regards,
    Csaba Nemeth
    CNCdrive Kft


To which I responded immediately, quoting your email to me with instructions and the discussion about the board failure.

cncdrive wrote:Then we finally identified your email and asked you about the content, because without knowing the package content we could not fulfill the customs papers.

That is also incorrect, I emailed you about sending it back and followed your instructions. My tracking information:

    August 10, 2020, 7:27 am
    Held in Customs
    BUDAPEST 1005, HUNGARY
    Your item is being held in Customs at 7:27 am on August 10, 2020 in BUDAPEST 1005, HUNGARY.

cncdrive wrote:But this was already too late and the post office said that the package was returned to the sender, because they do not store packages for more than 15days.

I am not pissed, but I am disappointed. This should have gone far smother. Ok, how do we get back to good customer service?
________________________________________________________________
Vance
CNC Router Parts 48/96, 23,
ST-M5045 drivers
/ETH-5LPT/UCSB
Carveco Maker
Vance
 
Posts: 24
Joined: Fri Feb 28, 2020 12:07 am
Location: Houston

Re: Phone Number for CNCdrive

Postby cncdrive » Tue Sep 29, 2020 7:21 pm

Vance,

I don't have you answers, my collegue was working on it and what I told you is exactly what he told me when I asked about your package.
Maybe he did not act with the paperwork on time, I don't know. But he said that the package was returned, but I will ask him again tomorrow, will ask him to ask the post office again.
cncdrive
Site Admin
 
Posts: 4887
Joined: Tue Aug 12, 2014 11:17 pm

Re: Phone Number for CNCdrive

Postby cncdrive » Tue Sep 29, 2020 7:25 pm

And I think that probably when my collegue emailed you about "what's in the package" then it was already too late.
Unfortunately in Hungary the post office is not like in the USA, they work very bad, we had several cases when they lost packages and they are usually unreachable, their phones are offline or always busy and their representatives do not even know how things work with customs etc.
This is why we ship with GLS and DHL only, we only ship via the post office to countries where GLS and DHL do not ship.

And I'm sorry for this problem. I will check after it again tomorrow.
cncdrive
Site Admin
 
Posts: 4887
Joined: Tue Aug 12, 2014 11:17 pm

Next

Return to Ask a question from support here

Who is online

Users browsing this forum: No registered users and 39 guests