Multi Head spindle (3 spindle)

[pinoy-cnc]

Hi UCCNC User and @cncdrive

Has any UCCNC user has done Multi head spindle in there machine. I have done this multi head using Masso G3 controller and i would like to do this also with UCCNC but i don't know were to start.
I am Using now a AXBB-E controller with this project. Maybe there is any user here that have done this kind of CNC Project.

Here is the video of the machine that i have done (3 spindle head) using Masso G3 controller.

https://youtu.be/zJwryrsPOaI

Thank you

Rex

[cncdrive]

Well you could write a macro for it which handles the different spindle speed commands and different start/stop signals for the spindles.
You could wire the analog 0-10Volts output to all 3 spindles and then wire separate start/stop signals and then you could call macros to switch the spindles on/off.
Ofcourse this way you can run the spindles on the same speed one time, because there is one analog output only on the AXBB-E.
I don't know if this limitation is a problem for you or not?

You could also use offsets G54, G55, G56 etc. to switch/select between the offsets of the different spindles.

[pinoy-cnc]

Thank you for the reply...
How can I assign the tool number for the lift spindle (spindle 1) and ro the right spindle (spindle 2) and the main spindle (center spindle)

Usually on Masso Controller the spindle 1 is assign to tool number 101 and the spindle 2 is tool number 102 and the main spindle is tool number 1 to 100 ( if your spindle is ATC)

Best regards

Rex

Well you could write a macro for it which handles the different spindle speed commands and different start/stop signals for the spindles.
You could wire the analog 0-10Volts output to all 3 spindles and then wire separate start/stop signals and then you could call macros to switch the spindles on/off.
Ofcourse this way you can run the spindles on the same speed one time, because there is one analog output only on the AXBB-E.
I don't know if this limitation is a problem for you or not?

You could also use offsets G54, G55, G56 etc. to switch/select between the offsets of the different spindles.

[ger21]

You need a custom M6 macro that activates the proper spindle based on tool number, and applies the correct offsets for each spindle.

[pinoy-cnc]

is there UCCNC user that can help me to write this Macro because, i don't have any idea were to start.

[cncdrive]

I think you should describe exactly how it should work, I mean like: If I press button X then it should do these things, if I press button Y then that should do these things, if I enter a number into this DRO then it should do these things etc., This would make things easier to understand about what you exactly want to achive.

I think you could simply use offsets and switch between them.

[pinoy-cnc]

I think you should describe exactly how it should work, I mean like: If I press button X then it should do these things, if I press button Y then that should do these things, if I enter a number into this DRO then it should do these things etc., This would make things easier to understand about what you exactly want to achive.

I think you could simply use offsets and switch between them.

Good Day, thank you for the reply. i done this multi spindle on Masso controller and i would like to do this also Using UCCNC Controller.

please see attached picture and video

https://youtu.be/5nBKM4Uqwd0?si=mIMZAArDd3DeYbGQ

https://youtu.be/DBr3-psD6yM?si=2iol9EXyOD3n_LbS

https://youtu.be/zJwryrsPOaI?si=djETtS2aWpm1pl-9

[arturod]

Very nice. Checkout how this guy did it:
https://www.youtube.com/watch?v=D8JZW_H_G2A

Arturo Duncan
https://cnc4pc.com