1000x500mm high precision router build - NEED FORUM HELP

If you milled something cool and you want to show it to others post it here.

Re: 1000x500mm high precision router build - NEED FORUM HELP

Postby NUDEcnc » Wed Sep 25, 2019 1:33 pm

Hi
the machine is up and running !!!
I have many hours of video showing build the final result. I hope to post BUILD blog ASAP.
For now, this is the "first run" video. Hope you will like it.

viber_image_2019-09-25_15-23-24.jpg

viber_image_2019-09-25_15-23-25.jpg

VIDEO
https://youtu.be/b28x_RwMkcU

At the moment I have a big problem. And I need HELP !!!

I can"t set up my VFD to work with UCCNC !!!
UCCNC with UB1
VFD is Sunfar E550. Manual for VFD: https://www.fasttobuy.com//download/2018-05-04/Sunfar_E550manual.pdf
I have rs456 to USB dongle.

Can someone please help me with this problem ??
I do have TeamViewer access to CNC machine so it should be easy diagnostics if my settings are any good.
Also, I would appreciate if forum users could go and verify my UCCNC settings.

Thank You for the support
CPU cooling made by me: http://www.nudecnc.eu
User avatar
NUDEcnc
 
Posts: 18
Joined: Fri Nov 09, 2018 8:24 pm

Re: 1000x500mm high precision router build - NEED FORUM HELP

Postby ger21 » Wed Sep 25, 2019 2:13 pm

I would use analog speed control, rather than modbus with RS-485, as it's much simpler.


UB1 ----- VFD

RPM

AH1 >>>>> VS
AO1 >>>>> AI
AL1 >>>>> GND

Start/Stop

NO1 >>>>> X1
CM1 >>>>> CM

You'll need to set the appropriate VFD parameters, but I don't have time to look them all up right now.
Gerry
UCCNC 2017 Screenset - http://www.thecncwoodworker.com/2017.html
ger21
 
Posts: 1861
Joined: Sat Sep 03, 2016 2:17 am

Re: 1000x500mm high precision router build - NEED FORUM HELP

Postby NUDEcnc » Wed Sep 25, 2019 6:40 pm

HI @ger21. Thank you for advise.
Yes, I did try analogue control with no luck.
I will try to go through VFD manual again. Thank you for your help.
EDIT:
Some progress:
I can adjust RPM by UCCNC.

I CAN't start spindle by UCCNC. But when I start Spindle from VFD panel and I press "Spindle CW(M3)" on UCCNC it will change spindle direction.
Any help.
Regards Arek
CPU cooling made by me: http://www.nudecnc.eu
User avatar
NUDEcnc
 
Posts: 18
Joined: Fri Nov 09, 2018 8:24 pm

Re: 1000x500mm high precision router build - NEED FORUM HELP

Postby ger21 » Wed Sep 25, 2019 10:50 pm

What do you have set for F0.02?
And F1.08?
Gerry
UCCNC 2017 Screenset - http://www.thecncwoodworker.com/2017.html
ger21
 
Posts: 1861
Joined: Sat Sep 03, 2016 2:17 am

Re: 1000x500mm high precision router build - NEED FORUM HELP

Postby NUDEcnc » Thu Sep 26, 2019 8:46 am

My settings:
F0.02 - 1000
F1.08 - 11 - FWD control
Regards Arek
CPU cooling made by me: http://www.nudecnc.eu
User avatar
NUDEcnc
 
Posts: 18
Joined: Fri Nov 09, 2018 8:24 pm

Re: 1000x500mm high precision router build - NEED FORUM HELP

Postby NUDEcnc » Thu Sep 26, 2019 9:46 am

Hi, I did check all the settings of the VFD.
My spindle is 4 pole 800Mhz 24000 water-cooled.
This is all the settings which are different from manual default.

0.00-1
0.02-1000
0.03-33.3
0.04-800.0
0.05-2.0
0.06-4.0
0.08-5.0
0.11-4.0
0.12-800
0.13-380
0.23-5.0
1.04-800
1.05-1
2.06-180
2.08-700
2.09-0
2.10-50
3.11-400
3.12-750
3.14-1216
3.24-0
5.12-20
5.13-300.0
5.14-20
5.15-300

Thank you for Your help.
Regards Arek
CPU cooling made by me: http://www.nudecnc.eu
User avatar
NUDEcnc
 
Posts: 18
Joined: Fri Nov 09, 2018 8:24 pm

Re: 1000x500mm high precision router build - NEED FORUM HELP

Postby NUDEcnc » Thu Sep 26, 2019 1:59 pm

Success !!!
Settings for F0.02-1001
ger21 wrote:I would use analog speed control, rather than modbus with RS-485, as it's much simpler.


UB1 ----- VFD
memberlist.php?mode=viewprofile&u=814
RPM

AH1 >>>>> VS
AO1 >>>>> AI
AL1 >>>>> GND

Start/Stop

NO1 >>>>> X1
CM1 >>>>> CM

You'll need to set the appropriate VFD parameters, but I don't have time to look them all up right now.


Special regards for ger21
CPU cooling made by me: http://www.nudecnc.eu
User avatar
NUDEcnc
 
Posts: 18
Joined: Fri Nov 09, 2018 8:24 pm

Re: 1000x500mm high precision router build - NEED FORUM HELP

Postby olivethehaas » Sat Jan 25, 2020 8:38 am

please what is the company who cut your granite plate for the machine ?
olivethehaas
 
Posts: 2
Joined: Sat Jan 25, 2020 8:33 am

Re: 1000x500mm high precision router build - NEED FORUM HELP

Postby olivethehaas » Sat Jan 25, 2020 8:47 am

NUDEcnc wrote:Hi
the machine is up and running !!!
I have many hours of video showing build the final result. I hope to post BUILD blog ASAP.
For now, this is the "first run" video. Hope you will like it.

viber_image_2019-09-25_15-23-24.jpg

viber_image_2019-09-25_15-23-25.jpg

VIDEO
https://youtu.be/b28x_RwMkcU

At the moment I have a big problem. And I need HELP !!!

I can"t set up my VFD to work with UCCNC !!!
UCCNC with UB1
VFD is Sunfar E550. Manual for VFD: https://www.fasttobuy.com//download/2018-05-04/Sunfar_E550manual.pdf
I have rs456 to USB dongle.

Can someone please help me with this problem ??
I do have TeamViewer access to CNC machine so it should be easy diagnostics if my settings are any good.
Also, I would appreciate if forum users could go and verify my UCCNC settings.

Thank You for the support



Hi Arek
what is the name of the company who machine your granite plate ?

best regards

Olivier
olivethehaas
 
Posts: 2
Joined: Sat Jan 25, 2020 8:33 am

Previous

Return to What you've made with your machine post the pictures, videos here

Who is online

Users browsing this forum: No registered users and 1 guest