Older UCCNC copy

If you have a question about the software please ask it here.

Re: Older UCCNC copy

Postby Robertspark » Tue Aug 07, 2018 9:30 pm

https://cncdrive.com/UCCNC.html

Two older versions are on the main page


I go as far back as 1.2026 (maybe a little older)
Robertspark
 
Posts: 1892
Joined: Sat Sep 03, 2016 4:27 pm

Re: Older UCCNC copy

Postby ger21 » Wed Aug 08, 2018 1:33 am

I have 1.0034, 1.012, 1.1022, 1.1026, 1.1027.
Which one do you want? I can upload them and send you a link.
Gerry
UCCNC 2022 Screenset - http://www.thecncwoodworker.com/2022.html
ger21
 
Posts: 2663
Joined: Sat Sep 03, 2016 2:17 am

Re: Older UCCNC copy

Postby ger21 » Wed Aug 08, 2018 2:00 pm

I'll get you a link this evening.
Gerry
UCCNC 2022 Screenset - http://www.thecncwoodworker.com/2022.html
ger21
 
Posts: 2663
Joined: Sat Sep 03, 2016 2:17 am

Re: Older UCCNC copy

Postby cncdrive » Wed Aug 08, 2018 2:16 pm

The 1.0034 is available for download on our website in the archives. It is the latest 1.0xxx version.
http://cncdrive.com/UCCNC.html
Just fully roll down the page and you will find the link to the download.
cncdrive
Site Admin
 
Posts: 4695
Joined: Tue Aug 12, 2014 11:17 pm

Re: Older UCCNC copy

Postby dezsoe » Wed Aug 08, 2018 3:40 pm

Umm... It's interesting. I installed the 1.0034 from the link and it sais, it's 1.0034, but only knows the UC100. I have an old download from 2014 October, version 1.0034 and it already knows the UC300_5LPT. Both shows in help/about 1.0034, but they are completely different. :o
dezsoe
 
Posts: 2049
Joined: Sun Mar 12, 2017 4:41 pm
Location: Csörög, Hungary

Re: Older UCCNC copy

Postby cncdrive » Thu Aug 09, 2018 12:39 pm

Make sure to delete the UCCNC.config file if you installed that early version over the 1.21xx version, because those new versions run on .net 4.0 and so the config file is required to allow to load 3rd party plugins,
but the old software installer does not delete the config file and also because it runs on .net 2.0 a config file is not installed.
And so if the new version's config file remains there then the app will crash because it tells Windows that the app requires .net 4.0 while it is .net 2.0 code.
cncdrive
Site Admin
 
Posts: 4695
Joined: Tue Aug 12, 2014 11:17 pm

Re: Older UCCNC copy

Postby cncdrive » Fri Aug 10, 2018 1:23 am

Then maybe the Flashplayer is missing from the computer or has the bug which was introduced at the time when we ported the whole UCCNC to OpenGL from Flash.
I did not follow up on if Adobe ever fixed that Flashplayer bug or not, because we no more needed it, so it is just a guess.
cncdrive
Site Admin
 
Posts: 4695
Joined: Tue Aug 12, 2014 11:17 pm


Return to Ask a question from support here

Who is online

Users browsing this forum: No registered users and 18 guests