1.2032 does not update firmware

If you think you've found a bug post it here.

1.2032 does not update firmware

Postby Derek » Tue Feb 07, 2017 10:26 pm

Just tried to test it out and it doesn't update the firmware.

Derek

EDIT:

UC300
Derek
 
Posts: 341
Joined: Mon Sep 05, 2016 9:57 am

Re: 1.2032 does not update firmware

Postby cncdrive » Tue Feb 07, 2017 10:32 pm

Hi Derek,

I think there is no new firmware for the UC300.
I don't remember any bugs which needed firmware change, but will ask my collegue tomorrow, he can confirm this.
cncdrive
Site Admin
 
Posts: 4695
Joined: Tue Aug 12, 2014 11:17 pm

Re: 1.2032 does not update firmware

Postby Derek » Tue Feb 07, 2017 10:49 pm

I tried to test the Q parameter for tapping. I did a test with one line with no Q and it went full depth the second line has a Q It makes the first Q pass, reverses and then sits with the spindle running. Like it's waiting for the index signal. I thought it might because of the firmware. But that doesn't make sense since it tried to do the Q. Any how I'm on 30140 FYI
Derek
 
Posts: 341
Joined: Mon Sep 05, 2016 9:57 am

Re: 1.2032 does not update firmware

Postby cncdrive » Tue Feb 07, 2017 11:13 pm

Could you please post that single line of code?
And you running this with the UC300-5LPT, the USB version, correct?
cncdrive
Site Admin
 
Posts: 4695
Joined: Tue Aug 12, 2014 11:17 pm

Re: 1.2032 does not update firmware

Postby Derek » Tue Feb 07, 2017 11:18 pm

UC-300 USB, M44B daughter board C-62 BOB

Code: Select all
N17G33.1 Z-0.6250 K0.04167 Q.125
Derek
 
Posts: 341
Joined: Mon Sep 05, 2016 9:57 am

Re: 1.2032 does not update firmware

Postby cncdrive » Tue Feb 07, 2017 11:22 pm

OK, thanks Derek. It is over midnight here, so I'll test your code tomorrow to see what the problem is.
cncdrive
Site Admin
 
Posts: 4695
Joined: Tue Aug 12, 2014 11:17 pm

Re: 1.2032 does not update firmware

Postby Derek » Tue Feb 07, 2017 11:30 pm

cncdrive wrote:OK, thanks Derek. It is over midnight here, so I'll test your code tomorrow to see what the problem is.


Slacker. :)
Derek
 
Posts: 341
Joined: Mon Sep 05, 2016 9:57 am

Re: 1.2032 does not update firmware

Postby cncdrive » Tue Feb 07, 2017 11:31 pm

Derek 2 more questions I forgot to ask:

From what Z height did you start the tapping. (Z=0 ?)
And when the first pass finishes and when you say it is just sitting and waiting, if you open the Diagnostics page is the Sync.Thread LED still on?

I may be able to get to the problem cause without answers to these, but maybe I will need the answers, so I thought it is better to ask now, so tomorrow I will better know what to look for.
cncdrive
Site Admin
 
Posts: 4695
Joined: Tue Aug 12, 2014 11:17 pm

Re: 1.2032 does not update firmware

Postby cncdrive » Tue Feb 07, 2017 11:31 pm

Derek wrote:
cncdrive wrote:OK, thanks Derek. It is over midnight here, so I'll test your code tomorrow to see what the problem is.


Slacker. :)


:)
cncdrive
Site Admin
 
Posts: 4695
Joined: Tue Aug 12, 2014 11:17 pm

Re: 1.2032 does not update firmware

Postby Derek » Wed Feb 08, 2017 12:08 pm

Hi Balazs

Tapping starts .25" above work. After the tap reverses out of the hole and is at clearance height the Sync.thread LED is on and the CCW spindle LED is on. The spindle is turning CCW.
Derek
 
Posts: 341
Joined: Mon Sep 05, 2016 9:57 am

Next

Return to Report a bug

Who is online

Users browsing this forum: No registered users and 10 guests

cron