UCCNC test releases posted in this thread

Post anything you want to discuss with others about the software.

Re: UCCNC test releases posted in this thread

Postby cncdrive » Fri Sep 08, 2017 5:23 am

UCCNC version 1.2043 is ready for testing.
The download link: http://www.cncdrive.com/UCCNC/setup_1.2043.exe

Bug fixes and changes:

- Altgr + characters like # were not accepted by the MDI, fixed.
- Colorpicker window startup position was changed to not show up out of screen.
- Support for the CNCroom -UB1 motherboard was added.
- Slider control acceptclick parameter was added, so the sliders can't be moved with click only with pull if this parameter is set false.
- In the toolpath viewer a plate with grid can be setup and viewed which plate can show the table working area.
- Some THC settings were not saved on closing, this issue was caused by the recent change of the Save settings function, fixed.
- THC anti-dive switch timing got a workaround to overcome the issue described in this thread: viewtopic.php?f=16&t=619&p=4545#p4545
cncdrive
Site Admin
 
Posts: 1475
Joined: Tue Aug 12, 2014 11:17 pm

Re: UCCNC test releases posted in this thread

Postby cncdrive » Thu Sep 14, 2017 10:57 pm

UCCNC version 1.2044 is ready for testing.
The download link: http://www.cncdrive.com/UCCNC/setup_1.2044.exe

Bug fixes and changes:

- UC300ETH and UC400ETH incorrect accleration calculation caused strange movements to the B-axis, fixed.
- UC300ETH and UC400ETH when the spindle encoder got enabled caused lost steps due to an interrupt priority problem of the encoder counter.
cncdrive
Site Admin
 
Posts: 1475
Joined: Tue Aug 12, 2014 11:17 pm

Re: UCCNC test releases posted in this thread

Postby cncdrive » Sat Sep 30, 2017 10:23 pm

UCCNC version 1.2045 is ready for testing.
The download link: http://www.cncdrive.com/UCCNC/setup_1.2045.exe

Bug fixes and changes:

- Rigid tapping codes set the Fset value to 0. The next motion in g-code execution reset the value properly, but if the motion was Cycle stopped on the rigid tapping g-code line that made the Fset to remain with 0 value which could possibly cause issues on the next g-codes execution, fixed.
- If e-stopped while homing an axis with a master-slave connection with separate home inputs, if the e-stop happened when the gantry squaring was executed, when the master and slave were disconnected to do the separate homing then the e-stop could cause the master-slave connection to remain breaked up, fixed.
- Interpolation problem in the CV optimiser for very small segments between arcs could cause a wrong interpolation of the small segment or arc, fixed.
cncdrive
Site Admin
 
Posts: 1475
Joined: Tue Aug 12, 2014 11:17 pm

Re: UCCNC test releases posted in this thread

Postby cncdrive » Wed Oct 25, 2017 10:41 pm

UCCNC version 1.2046 is ready for testing.
The download link: http://www.cncdrive.com/UCCNC/setup_1.2046.exe

Bug fixes and changes:

- Jog stuck in one direction if the axis' jog direction was changed very quickly with calling the opposite jog direction function, fixed. The jog also stuck into the original jogging direction if both jog keys were pressed in for the same axis, now when both pressed then the axis stops jogging.
- There was a global issue with the laser PWM handling effecting all controllers which appeared only in a few circumstances, fixed.
- Autoleveler plugin was updated. (Thanks Cahit!)
cncdrive
Site Admin
 
Posts: 1475
Joined: Tue Aug 12, 2014 11:17 pm

Re: UCCNC test releases posted in this thread

Postby cncdrive » Sun Nov 12, 2017 10:50 pm

UCCNC version 1.2047 is ready for testing.
The download link: http://www.cncdrive.com/UCCNC/setup_1.2047.exe

Bug fixes and changes:

- The M3 did not always enable the laser output (M10) in time, fixed.
- The Setoutpin function macro call caused the outputs to flicker in demo mode. This did not cause any real machine issue, because it effected the demo mode only, but we fixed the error now.
cncdrive
Site Admin
 
Posts: 1475
Joined: Tue Aug 12, 2014 11:17 pm

Re: UCCNC test releases posted in this thread

Postby cncdrive » Sat Dec 23, 2017 12:15 pm

UCCNC version 1.2101 is ready for testing.
The download link: http://www.cncdrive.com/UCCNC/setup_1.2101.exe

Bug fixes and changes:

- G41/G42 tool radius compensation g-codes were added.
- Function Getcurrgcodelinetext was added.
- Disable virtualmouse option was added.
- Canned cycle peck Q parameter reset with G80.
- Autoleveler plugin updated.
- Individual current hi/low output setting per axis.
- Enable delay setting to delay the enable signal when removing reset. Delay setable individually per axis.
- Home back off distance parameter was added. Setable per axis.
- Input signals debounce with setable time constant. 3 debounce parameters are separated for THC inputs, Home inputs and the rest of the inputs.
- Peak latency value was added to statistics window.
- IsMovingTHC function was added to detect when the movement paused because of lost arc event when THC control is used.
- Very small arcs appeared polygonal on the toolpath view, fixed.
- Console plugin was added to make plugins and macro debugging easier.
- Russian language was added to the installer.
cncdrive
Site Admin
 
Posts: 1475
Joined: Tue Aug 12, 2014 11:17 pm

Previous

Return to General discussion about the UCCNC software

Who is online

Users browsing this forum: No registered users and 3 guests

cron