UB1 Daughterboard - What features?

This Section is for users to discuss hardware

UB1 Daughterboard - What features?

Postby ger21 » Tue Dec 12, 2017 12:28 pm

Weerasak is considering offering a daughterboard for the UB1 breakout board, to use ports 4 and 5.

What features would you like to see on them?

Single port board, or 2 port board?

Mostly inputs, or mostly outputs?

NPN? PNP?
Gerry
UCCNC 2022 Screenset - http://www.thecncwoodworker.com/2022.html
ger21
 
Posts: 2663
Joined: Sat Sep 03, 2016 2:17 am

Re: UB1 Daughterboard - What features?

Postby Robertspark » Tue Dec 12, 2017 3:54 pm

I went with 2 x C10S boards
https://cnc4pc.com/motion-control/break ... -card.html

Take note that ports 4 & 5 of the UC300 are LPT input ports on pins 2-9, hence output is not an option (as far as I'm aware unless the firmware is to change for the UC300)

That being said, from my experience of using the C10S, more relays (NO+NC would be useful, high speed and maybe a few high current too (or the option to maybe buy and solder in some higher current relays if the board can be designed to accommodate both low current high speed and lower speed high current). As I have used the C10S for power 5v relays via its outputs.

The problem with the C10S is that its only 5v.....

Hence 24v would be useful given the UB1 is 24v

It may be worthwhile considering the use of something like the C35S with RJ45's for quick wiring via 8 core Ethernet cable which can be terminated quickly.
https://cnc4pc.com/motion-control/break ... board.html
Robertspark
 
Posts: 1892
Joined: Sat Sep 03, 2016 4:27 pm

Re: UB1 Daughterboard - What features?

Postby ger21 » Tue Dec 12, 2017 4:44 pm

Robertspark wrote:Take note that ports 4 & 5 of the UC300 are LPT input ports on pins 2-9, hence output is not an option (as far as I'm aware unless the firmware is to change for the UC300)


He mentioned the possibility of writing a plugin to possibly allow using them as outputs? Way over my head....
Gerry
UCCNC 2022 Screenset - http://www.thecncwoodworker.com/2022.html
ger21
 
Posts: 2663
Joined: Sat Sep 03, 2016 2:17 am

Re: UB1 Daughterboard - What features?

Postby ger21 » Tue Dec 12, 2017 5:01 pm

This is what he's thinking of:


-Second Charge Pump.

-13 npn isolated inputs 24V.

-13 npn/pnp isolated inputs 5v/24V.

-8 sink output same as mother board

It's probably 5-6 months away, though.
Gerry
UCCNC 2022 Screenset - http://www.thecncwoodworker.com/2022.html
ger21
 
Posts: 2663
Joined: Sat Sep 03, 2016 2:17 am

Re: UB1 Daughterboard - What features?

Postby alex_s » Tue Dec 12, 2017 6:36 pm

ger21 wrote:This is what he's thinking of:


-Second Charge Pump.

-13 npn isolated inputs 24V.

-13 npn/pnp isolated inputs 5v/24V.

-8 sink output same as mother board

It's probably 5-6 months away, though.


That's absolutely fine, and i would order one ;)
alex_s
 
Posts: 65
Joined: Tue Nov 29, 2016 11:45 am

Re: UB1 Daughterboard - What features?

Postby GF357 » Mon Dec 18, 2017 3:59 am

ger21 wrote:This is what he's thinking of:
-Second Charge Pump.
-13 npn isolated inputs 24V.
-13 npn/pnp isolated inputs 5v/24V.
-8 sink output same as mother board

It's probably 5-6 months away, though.


I'd buy one, as well.
GF357
 
Posts: 15
Joined: Wed Jul 05, 2017 11:30 pm
Location: Las Vegas, NV

Re: UB1 Daughterboard - What features?

Postby GF357 » Thu Feb 08, 2018 12:43 am

I saw over at cnczone that there's some renders of the board up. Hard to tell while looking at it on my cell phone... Any ideas on the dimensions?
GF357
 
Posts: 15
Joined: Wed Jul 05, 2017 11:30 pm
Location: Las Vegas, NV

Re: UB1 Daughterboard - What features?

Postby ger21 » Thu Feb 08, 2018 2:12 am

His original post showed it the same width as the UB1, which is 130mm. If the size stayed the same, it looks like it would be about ±75mm x 130mm.
Gerry
UCCNC 2022 Screenset - http://www.thecncwoodworker.com/2022.html
ger21
 
Posts: 2663
Joined: Sat Sep 03, 2016 2:17 am

Re: UB1 Daughterboard - What features?

Postby ger21 » Sat Mar 10, 2018 12:18 pm

A limited number of UB-1 daughterboards are now for sale at CNC Room. Not that there are two different versions.
http://www.cncroom.com/interface-cards/ ... anguage=en
Gerry
UCCNC 2022 Screenset - http://www.thecncwoodworker.com/2022.html
ger21
 
Posts: 2663
Joined: Sat Sep 03, 2016 2:17 am

Re: UB1 Daughterboard - What features?

Postby GF357 » Sat Mar 10, 2018 6:53 pm

ger21 wrote:A limited number of UB-1 daughterboards are now for sale at CNC Room. Not that there are two different versions.
http://www.cncroom.com/interface-cards/ ... anguage=en


I saw that a few minutes ago at CNCZone. Weerasak's link takes you to the NPN version. I'm thinking the universal version is a better choice because ... options, but I'm still assembling my "first" controller.
GF357
 
Posts: 15
Joined: Wed Jul 05, 2017 11:30 pm
Location: Las Vegas, NV

Next

Return to Hardware

Who is online

Users browsing this forum: No registered users and 11 guests