MODBUSEZ Plugin

This is where you talk about Plugins. How they are made and how they work, show examples.

Re: MODBUSEZ Plugin

Postby mrping » Sun Dec 16, 2018 9:21 am

it is version 49...
mrping
 
Posts: 20
Joined: Sat Dec 15, 2018 5:30 pm

Re: MODBUSEZ Plugin

Postby mrping » Sun Dec 16, 2018 9:28 am

The modbusez was old though upgrading it now
mrping
 
Posts: 20
Joined: Sat Dec 15, 2018 5:30 pm

Re: MODBUSEZ Plugin

Postby mrping » Sun Dec 16, 2018 9:39 am

Im running 49 version now with modbusez version 16. It is not saving my config, its reset every time I start UCCNC.
mrping
 
Posts: 20
Joined: Sat Dec 15, 2018 5:30 pm

Re: MODBUSEZ Plugin

Postby mrping » Sun Dec 16, 2018 10:02 am

changed min RPM to like 6000 and it worked (my spindle is 200 - 6000 though).
But the same thing occurs, spindle starts, stops in the middle of loading and then starts spinning again. No commands works.
Maybe it uses other registers ?
mrping
 
Posts: 20
Joined: Sat Dec 15, 2018 5:30 pm

Re: MODBUSEZ Plugin

Postby mrping » Sun Dec 16, 2018 10:16 am

spindle cw seems to be 0001
spindle ccw seems to be 0002
spindle off 0006

frequence is unknown
mrping
 
Posts: 20
Joined: Sat Dec 15, 2018 5:30 pm

Re: MODBUSEZ Plugin

Postby Dan911 » Sun Dec 16, 2018 12:17 pm

mrping does this use a Modbus protocol for serial communication??? If not ModbusEZ isn't going to work out of the box. The manual gives no info.

Dan
Dan911
 
Posts: 613
Joined: Mon Oct 31, 2016 1:22 am
Location: USA

Re: MODBUSEZ Plugin

Postby mrping » Sun Dec 16, 2018 1:08 pm

Yes and CW, CCW, stop works with modbusez plugin.
its only the rpm left.

Can i read it out someway ?
mrping
 
Posts: 20
Joined: Sat Dec 15, 2018 5:30 pm

Re: MODBUSEZ Plugin

Postby mrping » Sun Dec 16, 2018 1:10 pm

See pic
mrping
 
Posts: 20
Joined: Sat Dec 15, 2018 5:30 pm

Re: MODBUSEZ Plugin

Postby mrping » Sun Dec 16, 2018 2:09 pm

.
Attachments
20181216_144607.jpg
mrping
 
Posts: 20
Joined: Sat Dec 15, 2018 5:30 pm

Re: MODBUSEZ Plugin

Postby Dan911 » Sun Dec 16, 2018 8:31 pm

Yes with a Serial Monitor, you can try the free trial 1 here.>>> https://www.eltima.com/products/serial-port-monitor/

ModbusEZ divides you Max HZ with your max RPM and sends results in a high low byte in hex to register you input in settings.
For example with your settings, you set your RPM to 3000 it's going to send 25HZ (hex 00FA) or (09c4) depending on frequency resolution setting. Don't have time today but will take a better look at your manual tomorrow and see if I can help.

Dan
Dan911
 
Posts: 613
Joined: Mon Oct 31, 2016 1:22 am
Location: USA

PreviousNext

Return to Plugins

Who is online

Users browsing this forum: No registered users and 4 guests